Van

12 V to 230 V inverter for a van: what power to choose?

Continuous power, peak, pure sine wave, no-load consumption: how to choose a 12 V to 230 V inverter for a van, with a worked example.

Updated on 22 November 2026.

The short answer

To choose a 12 V to 230 V inverter, add up the power of the appliances you will run at the same time, add a margin, then check that the unit's continuous power, not its peak, exceeds that total. Then look at its no-load consumption: it sometimes weighs as much as a small appliance left plugged in all the time.

An inverter converts the battery's direct current into 230 V alternating current, the kind you find in a household socket. It is used to plug in a laptop charger, a kettle, a tool or a small kitchen appliance. If you only have phones and a laptop, USB and 12 V sockets are enough and you avoid conversion losses.

Continuous power and peak power

Datasheets give two figures that must not be confused. Continuous power is what the unit can supply for hours. Peak power is held only for a few seconds, long enough to start a motor or an electronic power supply.

Victron explains that its inverters can deliver a peak of more than about twice their continuous power, for short periods, and that the continuous power must cover the highest total demand, not just the largest appliance. Compressors, pumps and motors draw a surge of current at start-up: check this in the appliance's manual.

Temperature matters too. Continuous power ratings are given at 25 °C and fall when it is hot. In a van in midsummer, a closed compartment easily exceeds 40 °C: Victron's datasheet then gives a lower continuous power (see the table below).

How to calculate the power you need

The method has three steps. Note the power of each appliance you will use at the same time. Add them up. Add a margin: Victron advises adding 15% to the total power of the appliances when the inverter is under 1,000 W, and 10% above that.

Example: a 65 W laptop charger, a 500 W travel kettle and a 40 W tool battery charger used together make 605 W. With a 15% margin, that gives about 696 W. An 800 VA inverter rated at 650 W continuous at 25 °C would not be enough; you need to move up to the next model.

Another trap: heating appliances (kettle, toaster, hair dryer, hob) use a lot of energy in a short time. A 500 W kettle heating for 5 minutes draws about 42 Wh from the battery, plus the inverter's losses. The current on the battery side is very high, which calls for thick cables and a suitable fuse (see below).

A few models from Victron's Phoenix range, as an example

The table reproduces Victron's datasheet for the 12 V version of four models. It illustrates the order of magnitude and is not a recommendation: other manufacturers offer equivalent units. The values are those of the datasheet, with no measurement on our part.

Model (12 V)Continuous at 25 °CContinuous at 40 °CPeakMaximum efficiencyNo-load consumption
12/375300 W260 W700 W89%5.6 W
12/500400 W350 W900 W90%6 W
12/800650 W560 W1,500 W90%6.5 W
12/12001,000 W850 W2,200 W91%10 W

Pure sine wave or not: what it changes

The shape of the output wave is a selection criterion. A "pure sine wave" inverter reproduces the shape of mains current. Simpler models produce an approximated wave, which suits many appliances but can trouble some motors, some chargers or audio equipment. If in doubt, your appliance's manual states whether or not it accepts this type of wave.

Do not assume the waveform: look for the information on the manufacturer's datasheet. For example, Votronic states a pure sine 50 Hz output for its MobilPOWER SMI series. On the Victron Phoenix datasheet we read, the waveform is not specified in the text: if this point matters to you, check it on the product page before buying.

Efficiency and no-load consumption: the hidden cost

An inverter loses energy as heat. Datasheets give a maximum efficiency of about 89 to 91% for the models in the table, and it falls when the load is very low. For a 45 W laptop, count on about 50 Wh drawn per hour from the battery.

No-load consumption is sneakier. It applies whenever the unit is switched on, even with nothing plugged in. At 10 W no-load, a 12/1200 left on for 24 hours uses about 240 Wh per day, roughly the daily consumption of a compressor fridge according to our sizing guide. Victron also advises including the inverter's standby consumption in your daily budget.

Two remedies. The first: switch the inverter off when you are not using it, with a remote switch. The second: ECO mode, which Victron offers on the Phoenix range. The inverter then goes into standby and only switches on briefly at regular intervals (2.5 seconds by default) to detect a load. No-load consumption falls to about 1 W on the models in the table, but standby only wakes up if the load exceeds a threshold (15 W minimum in the datasheet): a small appliance below this threshold will not be detected. Votronic gives 5 to 8 W in standby and 0 W when off for its SMI models.

The battery side: cables, fuse, safety

A 1,000 W inverter at 12 V draws more than 80 amps on the battery side, and more once losses are counted (1,000 / 12 already gives about 83 A). This is a very high current: an undersized cable heats up, and a badly chosen fuse protects nothing. The terminals of a Phoenix 12/1200 accept up to 35 mm² according to the datasheet, and those of Votronic's SMI 1200 series use two 50 mm² cables: these orders of magnitude show how far we are from the wires of a lighting installation.

Victron details the sizing of DC cables and fuses in its book Wiring Unlimited. Read it, then have your installation checked.

On the 230 V side, the danger is real: a poorly protected installation can cause electrocution or a fire. For any fixed wiring, any socket installed in the vehicle, any connection to a campsite supply, call a professional electrician. This guide does not guarantee the compliance of any installation. See also our guide on regulations and electrical safety.

Sources

Safety. This guide is for information only and replaces neither the manufacturer's instructions nor a professional's advice. For 230 V, high currents and any fixed installation, call a qualified professional.

Also worth reading

Calculate my needs

Transparency. Solanomad is funded by affiliate marketing, but this version of the site contains no partner or merchant links for now: no commission is linked to your clicks here. Learn more.