The short answer
Yes, you can recharge your van's battery while driving, and the clean method uses a DC-DC charger placed between the starter battery (or the alternator) and the leisure battery. It sets the charging voltage and current itself, which a simple wire does not.
It complements solar: in winter or in overcast weather, an hour on the road can supply a good share of the missing energy. This page explains the principle, the points to check before buying and the wiring precautions. It does not replace an installer: the currents involved are high.
Why not simply connect the two batteries?
Connecting a leisure battery directly to the alternator works with some lead batteries, but causes problems as soon as the chemistry changes or the alternator is "smart". Victron, in the manual for its Orion-Tr Smart chargers, states that controlled charging is "essential" with a smart alternator, whose voltage varies and which is switched off when it is not needed.
The same manual explains that the low internal resistance of a lithium battery can overload the alternator in direct charging: the DC-DC charger therefore limits the current. It also applies a three-stage charging cycle (bulk, absorption, float), adapted to the chemistry selected in the manufacturer's app.
One last benefit: it separates the starter battery from the leisure battery when the engine is off, which avoids draining the battery that starts the vehicle.
What the charger must be able to do
Datasheets vary from one manufacturer to another. Here are the points to check on the datasheet of the model you are considering.
- Detection of the running engine: the charger should only work when the alternator is supplying current. On Victron it is built in, with an option to control it from the ignition switch.
- Smart alternator compatibility: adjustable start and stop thresholds, or a setting provided for this case.
- Charging profile for your battery (AGM, LiFePO4 lithium): to be chosen in the app or by a switch.
- Input and output voltage range, and maximum output current in amps.
- Isolated or non-isolated: an isolated model electrically separates input and output. The Victron manual consulted does not detail the difference; read the datasheet of the model you have in mind.
- Reverse polarity protection: the Victron manual states that its Orion-Tr Smart units do not have it and that damage is not covered by the warranty. Check this point on any model.
What current, what energy
The output current sets the charging speed. The calculation is simple: energy added in Wh = voltage x current x time. The energy actually stored is slightly lower because of losses in the charger and the cables. The following table is therefore an order of magnitude, calculated for a 12 V leisure battery with a constant current and no losses. A town trip with frequent stops will give less, because the alternator does not always supply the current requested.
| Output current | Power at 12 V (approx.) | Energy after 1 h of driving (approx.) | Energy after 3 h (approx.) |
|---|---|---|---|
| 10 A | 120 W | 120 Wh | 360 Wh |
| 20 A | 240 W | 240 Wh | 720 Wh |
| 30 A | 360 W | 360 Wh | 1,080 Wh |
| 50 A | 600 W | 600 Wh | 1,800 Wh |
Wiring: what really matters
The DC-DC charger connects in direct current, but with currents that heat up a cable that is too thin. For the non-isolated Orion-Tr Smart family, Victron's manual specifies a battery protection fuse and a cable size depending on the cable length. At 12 V, it indicates a 60 A fuse and the sizes below.
| Cable length | Minimum size (12 V, 60 A fuse) |
|---|---|
| 0.5 m | 6 mm² |
| 1 m | 10 mm² |
| 2 m | 10 mm² |
| 5 m | 16 mm² |
| 10 m | 16 mm² |
Installation rules to remember
These values come from the manual of one model family: for another manufacturer, or another current, they differ. Always follow the table in your appliance's manual. Victron's book "Wiring Unlimited" gives the general rule: a fuse on the positive cable of each consumer, and a voltage drop kept below 2.5%.
- Use flexible, fine-stranded copper cable, as Victron requires, and respect the stated tightening torque (1.6 Nm on the terminals in this manual).
- Fit the fuse on the positive wire, with a rated voltage at least equal to that of the circuit.
- Check the polarity twice before connecting the battery; connect the cables to the charger first, then to the battery.
- Place the charger near the leisure battery but not directly above it, to avoid battery gases (advice from the manual).
- Too large a voltage drop on the input cable can stop the charger from starting, even if the alternator is fine: keep the cables short and thick enough.
Safety and professionals
A short circuit on a vehicle battery can melt a cable in a few seconds. A wrong fuse, a loose lug or a cable rubbing against the bodywork are the classic causes. Call a professional if you are not used to high currents, and especially if the vehicle has a smart alternator or a stop-start system, whose behaviour depends on the model.
Nothing here is a guarantee of compliance: the installation remains your responsibility, and a fixed conversion can have consequences for insurance and the roadworthiness test (see the dedicated guide).
Sources
- Victron Energy, Orion-Tr Smart DC-DC (non-isolated): introduction
- Victron Energy, Orion-Tr Smart DC-DC (non-isolated): features
- Victron Energy, Orion-Tr Smart DC-DC (non-isolated): installation, cables and fuses
- Victron Energy, Wiring Unlimited: DC wiring
Safety. This guide is for information only and replaces neither the manufacturer's instructions nor a professional's advice. For 230 V, high currents and any fixed installation, call a qualified professional.