The short answer
The power calculation is the same as for a van: you add up the needs in watt-hours per day, then work out the panels. What changes is the environment: water, salt, vibration, wind and available space. A boat or a roof tent therefore needs components designed for outdoor use and careful fitting.
This page replaces neither the manufacturer's manual nor a professional, especially on a boat, where direct current and batteries call for precautions.
Boat and roof tent: two different situations
On a boat, panels are often fixed (bimini, coachroof, arch) or flexible (deck). Spray, corrosion and shade cast by the rigging or ropes all matter. A boat is also a place where an electrical failure has immediate consequences.
On a roof tent, the panel is often folding or placed on the roof rack, and the battery is in the vehicle or in a small box. The constraints are weight on the roof, wind resistance while driving and rain on exposed connections.
IP rating: how to read it
The IP rating (standard IEC 60529) has two digits: the first concerns dust, the second water. An X means no data is available for that criterion. Do not confuse "resistant to splashing" with "waterproof against immersion": these are different tests.
| Rating (extract) | What it describes (according to the standard) |
|---|---|
| IPX4 | water splashed from any direction has no harmful effect |
| IPX5 | water jets from a 6.3 mm nozzle, from any direction |
| IPX6 | powerful jets from a 12.5 mm nozzle |
| IPX7 | immersion down to about 1 m for 30 minutes |
| IPX8 | continuous immersion under conditions set by the manufacturer |
| IP5X / IP6X | dust: 5 = protected, 6 = dust-tight |
Points of attention for water
A panel's IP rating does not tell the whole story: the junction box, the connectors and the controller each have their own rating, which may be lower. Many controllers are designed for indoor use: they must stay dry, near the battery. A high rating is not a promise of long-term resistance in salt water either: look at what the manufacturer says about marine use.
- Note the IP rating of each outdoor element (panel, box, connectors), not just the panel.
- Keep the controller sheltered, unless it is stated as suitable for outdoor use.
- Make drip loops in the cables before hull or roof passages.
- Check the connections regularly: salt and damp corrode them.
- Do not connect the positive or negative of the panels to earth: Victron asks for the frames to be connected, not the poles.
What power?
Start from your appliances: lights, pump, fridge, instruments, phone. Multiply the power of each by its time of use to get the watt-hours per day, then divide by the hours of full sun and by an overall efficiency of 0.6 to 0.75 to allow for losses. Worked example, for illustration: a need of 300 Wh per day with 4 hours of full sun and an efficiency of 0.7 calls for about 300 / (4 x 0.7), or about 107 W of panel.
On a boat, the shade of a mast or a rope on a single panel can sharply reduce output: it is better to allow a margin. On a tent roof, the surface limits the power: measure the space before choosing.
Fitting: fixing without weakening
On a tent roof as on a deck, each hole is a possible entry point for water. Where possible, prefer glued fixings or rails designed for this use, and follow the mount's manual. A folding panel placed on the ground or on the roof, connected by an extension lead, is an option that avoids drilling: the guide on folding panels and power stations details the advantages and limits.
Think about wind too. A panel over a metre long acts like a sail when driving or at anchor. On a boat, the fitting area must avoid hindering manoeuvres, sails and access, and orientation matters less than shade: a flat panel in shade produces very little.
On a roof tent, check the maximum load permitted on the roof and on your vehicle's roof bars, stated by the manufacturer: adding the tent, the panels and their mounts may exceed this limit.
Controller, battery and safety
An MPPT or PWM controller is installed between the panels and the battery; Victron's manual restates the order of connection: battery first, panels next. Each circuit has its fuse on the positive wire. On a boat, the battery and cables are subject to their own rules: consult a marine professional.
None of this information guarantees the compliance of your installation. A badly fixed panel can fly off while driving or at sea, and a badly protected cable can heat up.
A worked example for a weekend
Take a small sailing boat or a roof tent with 20 W LED lighting for 4 hours (80 Wh), a phone and a tablet charging (about 35 Wh) and a 50 W pump for 12 minutes (10 Wh). The need is about 125 Wh per day. With 4 hours of full sun and an efficiency of 0.7, you need about 125 / (4 x 0.7), or about 45 W of panel.
This result is a minimum: if there is a fridge, consumption climbs quickly (count several hundred watt-hours per day, see the guide on appliance consumption), and November sunshine is not July sunshine. Go back to the site's calculator to test your case month by month.
Sources
- Wikipedia (English), IP Code: definition of protection ratings (IEC 60529)
- Victron Energy, SmartSolar MPPT 100/30 and 100/50 manual: installation
- Victron Energy, Wiring Unlimited: DC wiring
Safety. This guide is for information only and replaces neither the manufacturer's instructions nor a professional's advice. For 230 V, high currents and any fixed installation, call a qualified professional.