The short answer
A "complete" solar kit for a van is almost never complete: it generally contains the panels and the charge controller, sometimes the cables and mounts, and more rarely the battery, fuses and inverter. Before buying, compare the exact list of contents with what your installation requires.
A kit has a real advantage: the main elements are chosen to work together. It also has a limit: it fixes the power, and you cannot always expand it.
What a typical kit contains
The contents vary a great deal. Here, as an example, are two kits described by their manufacturer Renogy: a 200 W kit made up of two 100 W panels with a 40 A MPPT controller and a Bluetooth module, and a 400 W kit made up of two 200 W panels with a 40 A controller. They contain no battery. This is not a recommendation: it is an example of what a datasheet specifies.
- Solar panels: number, power in watts-peak, dimensions and weight.
- Charge controller: type (MPPT or PWM), maximum current and maximum input voltage.
- Cables and connectors: length, cross-section, connector type (often MC4).
- Mounting brackets: sometimes supplied, sometimes to be bought separately.
- Fuses and circuit breakers: rarely included; they depend on your wiring.
- Battery, inverter and battery charger: generally outside the kit, except all-in-one "power stations", which are a different product.
Compatibility pitfalls
The first pitfall is voltage. Victron's manual for the SmartSolar 100/30 and 100/50 controllers states that the panels' open-circuit voltage cannot exceed 100 V and that the nominal voltage must exceed the battery's by at least 5 V. This open-circuit voltage rises when it is cold: you must therefore take the panel's temperature coefficient into account when placing panels in series.
Second pitfall: the battery type. A controller must be able to adjust its charging voltage for your chemistry (AGM or lithium). Check this setting on the datasheet.
Third pitfall: a set that cannot grow. If the controller only supports 200 W, adding a third panel means changing the controller.
- Check the total open-circuit voltage (Voc) of the panels in series, when cold, against the controller's limit.
- Check the controller's output current against the panel power and the battery voltage.
- Check the roof space before buying: the dimensions are on the datasheet (for example 865 x 578 mm for a 100 W panel in the kit cited).
- Do not use panels fitted with optimisers with an MPPT controller unless the manual allows it: Victron forbids it for its controllers.
Reading a kit's datasheet, line by line
Three lines deserve a close look. The kit's power is the sum of the panels' power under test conditions: on the roof, real output is lower because of heat, shade, cables and the controller. An overall efficiency of 60 to 75% is a common order of magnitude; it is used in the site's sunshine data.
The length of the supplied cables matters too. The longer a cable, the more voltage it loses, and Victron recommends staying under a 2.5% voltage drop. If the kit's cables are too short for your run between the roof and the controller, you will need to buy more, with the right cross-section.
Finally, look at what the manufacturer says about the warranty: reverse polarity and overvoltage are often excluded. The Victron manual cited below states this for its controllers.
A table for comparing two kits
The data below come from the manufacturers' datasheets (Renogy, pages cited below). They serve to show what to compare, not to name a best kit.
| Criterion | 200 W kit (example) | 400 W kit (example) |
|---|---|---|
| Panels | 2 x 100 W | 2 x 200 W |
| Size of one panel | 865 x 578 x 30 mm | 1,262 x 764 x 30 mm |
| Controller | MPPT 40 A | MPPT 40 A |
| Controller input voltage | not noted here | 15 to 100 V |
| Battery included | no | no |
| Question to ask | Do 2 panels of 100 W fit on my roof? | Do 2 panels 1.26 m long fit on my roof? |
The limits of a kit
A kit is sized for a power, not for your needs. First calculate your consumption in watt-hours per day, then choose the panel power: the sizing guide and the site's calculator are for that. Only then look for a kit that matches.
A kit does not settle the question of safety either: fitting, fuses and cable cross-section remain your responsibility. For high currents, call a professional.
Kit or separate parts?
Take a kit if you want a simple base with compatible elements, and if its power matches your need. Choose the parts separately if your roof has an unusual shape, if you want to expand later or if you already have the battery. In both cases, read the manuals before drilling the roof: a badly sealed installation lets water in.
Checklist before ordering
Before confirming a kit, go over this list again. If an answer is missing on the datasheet, ask the seller rather than guessing.
- My need in Wh per day is calculated, and the kit's power meets it with a margin.
- The panels fit on my roof without overhanging, with room for the brackets and cables.
- The total open-circuit voltage stays under the controller's limit, even in cold weather.
- The controller accepts my battery's chemistry.
- The cables are long enough and of sufficient cross-section, and I have planned the fuses.
- I know who will fit the kit and how the roof will be made watertight.
Sources
- Renogy, 200 W solar kit (2 x 100 W) with Rover 40 A controller
- Renogy, 400 W premium solar kit (2 x 200 W) with Rover 40 A controller
- Victron Energy, SmartSolar MPPT 100/30 and 100/50 manual: installation
Safety. This guide is for information only and replaces neither the manufacturer's instructions nor a professional's advice. For 230 V, high currents and any fixed installation, call a qualified professional.